How to Factory Reset a JVC Car Stereo

How to Factory Reset a JVC Car Stereo

To reset your JVC vehicle audio, you must follow the instructions carefully. You never want to have your radio suddenly fall quiet when you’re traveling along a highway. Troubleshooting typical JVC vehicle radio issues with a hard reset is the focus of this article.

What we’ll cover is a wide range of ways, depending on the model you have. So, without further ado, here we go!

Hard Reset JVC Single-DIN In-Dash Receivers

JVC stereos, in contrast to Pioneer and Kenwood models, are very simple to reset. Do this, and this, and this, and this.

a) Remove the Faceplate

Begin by taking off the faceplate. Wiggle it around until the clamps fall undone and it’s free.

The faceplate’s eject button is located at the bottom left of the screen. Press the button and carefully remove it from the system.

b) Find the Reset Button

There is a reset button you’ll need to find. In terms of size, it shouldn’t be too difficult to find.

If you’re stumped, you may go to your stereo’s owner’s handbook to find out which reset button is located on the back. JVC stereos often have it in the middle.

c) Reset the Unit

A sim ejector pin or paper clip can be used to push and hold for around five seconds.

Within five seconds of removing faceplate, push the reset button. Because of this, it is best to be ready to do the assignment quickly.

d) Re-attach the Faceplate

Check the faceplate to determine whether it’s attached correctly.

JVC KD-T711BT, JVC KD-T710BT, KD-TD710BT, KD-SR86BT models are tested for this method In theory, it should also work with other models of the same type.

Factory Reset JVC Double DIN Car Stereos

Factory Reset JVC Double DIN Car Stereos

Only a few minor differences exist between resetting a single din and resetting a double din. What you must do is as follows:

i) Disconnect USB Device

Disconnect any USB devices from the computer.

Unplug it if you have one. Resetting a USB device when it is attached to the stereo might result in the USB device malfunctioning or losing data.

ii) Find the Reset Button Hole

The volume control knob is flanked by a reset button on Double DIN systems. Try to discover a gap in the wall. The user handbook that comes with the head unit is a great place to start if you’re stuck.

The reset button is often situated on the side of entertainment devices without any physical buttons or volume control knobs.

iii) Reset it

Continue in the same manner. A toothpick, a sim ejector pin, or a paper clip can be used to press and hold the button until the machine reboots.

Aside from the JVC KW-X840BTS and KW-M560BT double-DIN versions, the procedure is applicable to other models. The JVC KW series, in particular, should be compatible.

Factory Resetting Old JVC Models

This procedure should work with some older JVC stereo units that don’t have a reset hole. Make sure you follow the directions exactly.

1. Eject CD or USB Drive

If you have a CD or USB drive inserted, remove it from the computer. This is a precautionary measure to protect the data stored on the disk.

2. Press On and Select Button

Hold down the SELECT and ON buttons simultaneously for around 5 to 8 seconds so that your stereo’s settings can be restored to their factory defaults.

Why Do I Need to Reset JVC Radio?

In order to get rid of any unwanted settings or configurations kept in your JVC stereo, you need to reset it.

[su_youtube_advanced url=”″]

As an example, if your JVC head unit continues to change radio stations even after you delete your presets, it may be due to a settings failure. These undesired settings can be removed by resetting. Here are some of the most frequent issues that may be solved with a simple reset.

a) Get Rid of Protect Mode

Resetting your JVC stereo is one of the few methods for removing or disabling the protection mode.

Many automobile owners find themselves in a bind when the mode is activated for no apparent reason. To fix this, all you need to do is reset the device to its factory settings condition.

b) Solve H/W Error

If your JVC stereo is giving you a H/W Error warning, it’s possible that the head unit is broken.

The error code is usually caused by a hardware malfunction or other issue with disc and memory card reading. Although the system appears to be functioning normally, an error may nonetheless occur from time to time. Resetting the device’s factory settings is the only option to get rid of this problem.

c) Slow or Laggy Head Unit

If your head unit is sluggish or laggy, it may be because the system has too many options and configurations that are slowing it down.

If the storage area is overflowing with data, certain functionality, such as changing songs on USB devices or SD cards, may suffer. All the superfluous data may be deleted if the device is reset to factory defaults.

d) Can’t Find What’s Wrong with it

This is a common complaint from consumers who are baffled as to why the system abruptly stopped working.

Try resetting the JVC stereo system if you find yourself in this situation.

The most effective technique to tackle some issues that cannot be solved by any other means. If you follow a few easy instructions, you’ll be back to your old self in no time!


JVC head units have a reset button that is either tucked beneath or next to the volume control knob on nearly all of them. If you don’t know how to accomplish this, you’ll need to hold down both the ON and SELECT buttons for 5-8 seconds. If everything else fails, consult your model’s owner’s handbook to learn how to do a factory reset.

Leave a Comment

Your email address will not be published. Required fields are marked *